Restore original Uboot for Pogoplug V3 (2 replies)
Hello, I have a Pogoplug V3 (POGO-P24) and installed successfully Arch Linux on it. At the moment I want to use the original software from Cloud Engines, but the Uboot for Arch Linux has disabled it....
View ArticleGoFlexNet Bricked after installing Mainline U-Boot (no replies)
I happened to have the perfect GoFlexNet setup, latest uBoot, netconsole enabled, recovery enabled, I was using Archlinuxarm, I went ahead and installed mainline uBoot, which removed all the...
View ArticlePogoplug Mobile - enable SD card booting from Linux? (3 replies)
I've been working on my Pogoplug Mobile for a couple months now, (I only get an hour or two at a time to play with it), and I've finally got it up and running. I want to enable booting from the SD...
View ArticleAbility to add extra Linux kernel parameters (2 replies)
Bodhi, I just saw that zswap was supported in your kernel. I want to enable that. zswap.enabled=1 Is there a good way to specify that in uboot?
View ArticlePogoplug E02 Bad Block, with questions about installing the U-Boot software...
Hi all, I have a problem with a bad block coming up when I try to install the U-Boot software on my black pogoplug E02. I’m am following the directions here:...
View ArticleDo I have the correct uBoot installed? (12 replies)
Using a GoFlex Home base, I ran this procedure: cd /tmp wget http://projects.doozan.com/uboot/install_uboot_mtd0.sh chmod +x install_uboot_mtd0.sh ./install_uboot_mtd0.sh I have a USB stick plugged in...
View ArticlePogoplug mobile instalation went hideously wrong (10 replies)
So I purchased a Pogoplug Mobile last week and wanted to play around with installing arch linux on to it. I was following the guide here...
View ArticleTotaly f***ed up my Goflex Home uBoot (11 replies)
Hello, i have semi-bricked my Goflex Home. Updated uBoot and set up some wrong stuff in uBoot-Config. I have working UART, but all i see is: U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:41:47) Seagate...
View ArticleWhich uBoot best to use for E02? (1 reply)
Hi everyone, New to the forum. I have a new pink E02 that I'm looking to install Arch (or possibly Debian) on. I already have one running Arch (see my experience with it here). I was wondering what...
View ArticlePogoplug V4 Mobile won't boot after installing Qui's uBoot (1 reply)
I have a Pogoplug V4 Mobile that was running Arch Linux using the uBoot from their site. It was running fine. But I tried to upgrade to Qui’s uBoot at...
View ArticlePogoplug E02 upgrading U-boot. Bad block detected. (6 replies)
Hi, I was reading the guide on how to update the uBoot for Pogoplug E02. And I've detected bad block. 1. What should I do? 2. Also is it safe to upgrade the uBoot from Archlinux on usb or do I need to...
View ArticlePogoplug E02 problems with u-boot (3 replies)
pogoplug e02 I am unable to see anything through putty, my USB to TTL Converter is http://www.ebay.com/itm/New-1PCS-5PIN-PL2303-USB-To-TTL-Auto-Converter-Adapter-Module-unit-For-arduino-/141150349286...
View Articlemy Pogoplug v4 dead after Nand flash (1 reply)
Hi all, I bricked my seconde Pogo v4 ( I don't remember how that happen ) and my big problem is when I tried to revert back the stock firmware to mtd0 with serial/UART and tftp I did something wrong...
View ArticlePogoPlug V4 won't boot after failed env input (1 reply)
Hello everyone, I was trying to do a reinstall of arch on my pogoplug when the power in the part of the house where the pogolpug was connected went down. My pogo didn't start correctly so I soldered a...
View ArticleU-Boot VAMP 0.6 Pogoplug V4 (no replies)
I have a collection of Pogoplugs thank's to the great U-Boot on here, brilliant little devices. I also have serial access on them all. On one of them I run VAMP 0.6 as a music player, I have tried a...
View ArticleGoflex net bad blocks and no boot. (6 replies)
Hi, Please help. After install new uboot (2014.07) and rootfs my Goflex net "bricked". With Serial Jtag I see I have bad blocks on flash. I realized it during uboot install, but because my nandwrite...
View ArticlePogoPlug E02 uboot, cannot stop autoboot (5 replies)
Hi everyone! My PogoPlug E02 won't boot after I flashed it to the latest U-Boot referenced in the PogoPlug E02 Arch Linux installation instructions. I get the following from my PogoPlug's serial...
View ArticlePogoplug e02 boot from iscsi (1 reply)
Hello, I was wondering if it's possible to boot Debian Wheezy from a iscsi NAS? Goal is to remove the USB device from the Pogo (I have a total of 5). Other possibility is to only load system and swap...
View Articlehas any one installed debian on a ix2-dl (no replies)
i need help with running debian on a ix2-dl Processor : Feroceon 88FR131 rev 1 (v5l) BogoMIPS : 1589.24 Features : swp half thumb fastmult edsp CPU implementer : 0x56 CPU architecture: 5TE CPU variant...
View ArticleBootting off network (1 reply)
I haven't been following up with this forum for quite sometimes. So, I am probably a bit dusty (outdated) w.r.t. the current u-boot version. Anyway, I have a Seagate GoFLEX NET (with a 2TB SATA HDD)...
View Article