PogoPlug E02 uboot, cannot stop autoboot (5 replies)

Hi everyone!

My PogoPlug E02 won't boot after I flashed it to the latest U-Boot referenced in the PogoPlug E02 Arch Linux installation instructions.

I get the following from my PogoPlug's serial output when I boot it:

U-Boot 2014.04.R3-1 (May 26 2014 - 19:45:55) Arch Linux ARM
Pogo E02

SoC:   Kirkwood 88F6281_A0
DRAM:  256 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot:  0
PogoE02>
PogoE02>
PogoE02>
PogoE02> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>> U-Boot 2014.3>>>

I cannot get to the PogoE02> prompt when I hit a key just after U-Boot starts up- my PogoPlug just prints the "U-Boot 2014.3>>>>", PuTTY "beeps" and I can't type "printenv" or anything else at the PogoE02> prompt. PuTTY just beeps the ASCII "bell" when I hit a key.

I get the output above with or without the USB stick I installed Arch Linux to inserted into a USB port on my PogoPlug.

Is there anything I can do to keep it from printing "U-Boot 2014.3>>>>" and actually be able to type commands at the PogoE02> prompt?

I get the above output with or without the USB drive I installed Arch Linux to plugged into a USB port on my PogoPlug.;

I remember getting errors when I was installing Arch Linux to the USB stick but U-Boot flashed OK (I don't remember seeing any errors).

Thanks in advance for any help you can provide!