NSA325 v2: stuck on Bad Magic Number (no replies)
Hi Forum! what a pity I found you only a few hours ago. I have a NSA 325 v2: a friend told me that I can put Debian on it.. googling NSA325 debian I went to the wrong wiki :(...
View ArticleNSA310 broken after 2017.07 U-Boot Kirkwood (no replies)
I tried flashing new uboot and failed. There was no flash_erase command so I used flash_eraseall mtd0, probably my mistake. Then I flashed nandwrite /dev/mtd0 uboot.2017.07-tld-1.nsa310.mtd0.kwb - it...
View ArticleNSA325 - kernel panic, Cannot open root device "(null)" (powerloss while...
Hello, I tried to do the initial install of the NSA325 with linux-4.12.1-kirkwood-tld and rootfs. I head a powerloss before the reboot. Status: Since there is a lot of awesome information in this...
View ArticlePointers for porting U-Boot 1.1.4 source to more current U-Boot (1 reply)
bodhi, I am wondering if you have any pointers on porting 1.1.4 version U-Boot for a Kirkwood device to a more current U-Boot? The structure of U-Boot appears to be quite different, so I'm looking for...
View ArticleStubborn Stora (1 reply)
Hi, I hope anyone can help me to put one of my stora in right working order. For the last three months I've been using one of my stora after having flash the last u-boot available from bodhi and...
View ArticleTrouble booting new drive (1 reply)
I'm attempting to upgrade the HDD I have attached to my pogoplug v4 mobile from a 1TB to a 4TB. To support a single partition greater than 2TB, I'm using a GPT partition table rather than an msdos...
View ArticlePogoplug Wont Accept Commands after interrupt (2 replies)
Hello, I decided to give hacking one of these a try. Its seems as though any command I send through putty is not getting executed. Uboot does recognize the interrupt but does nothing after. Any...
View ArticleNETGEAR STORA - Bad Magic Number (no replies)
Hi, in the last week my old Stora won't boot anymore. After that I've follow different tutorial and I've dump the u-boot log with a USB to TTL serial converter. __ __ _ _ | \/ | __ _ _ ____ _____| | |...
View ArticleFlash NAND with bad blocks (no replies)
Hello, I am posting here as somebody proposed this on the OpenWrt forum, please tell me if it's not the right place. I would like to install OpenWrt on an NSA310. The installation instructions are to...
View ArticleNSA325v2 bad block, can I flash it? (no replies)
Hello, first of all I have to admit I have no experience with flashing u-boot, this is my first time doing it so I want to be as careful as possible. Why am I doing it? Well, I tried to update my...
View ArticleNSA-325 Bricked ? HDD2 LED constantly active (2 replies)
Hey :/ i have a problem with my NSA325 v1. The NAS did not respond. I turn it on an off by pull out the energy connection. I try to reset without any success, the NAS make no noise (Beep). The NAS get...
View ArticleGoFlex Home gone AWOL (no replies)
I have a GoFlex Home unit which I messed about with about a year ago and must have installed a new uBoot. Unfortunately I can no longer access it. When I switch on with no disk, the green light blinks...
View Articlesaveenv (1 reply)
When the saveenv command is issued, is there any indication that it has completed successfully? I changed a couple of environment variables and waited and waited to see some acknowledgement, but saw...
View ArticleOpenWrt installation failure (3 replies)
I followed this guideline https://openwrt.org/toh/seagate/goflexhome for installing OpenWrt on a GoFlex Home unit but unfortunately on reboot it didn't boot OpenWrt :( ... NAS>> reset...
View ArticlePogoplug V3 SATA direct booting (no replies)
I've updated the u-boot release thread to add a link to where to download the SATA direct booting files. QuoteReferences: ... 3. SATA direct booting tarball.
View ArticleUnderstanding my environment (1 reply)
I've recently tried to get my U-Boot 2017.05-tld-2 working again - the one with bootelf for FreeBSD, and I don't undestand the environment I have or where it comes from.... -Boot 2017.05-tld-2 (Jul 26...
View ArticleBooting with kwboot (3 replies)
How can I tell if I have a uBoot? I may have zapped it in a previous attempt to install OpenWrt. I am currently trying to boot using kwboot with uboot-2017.07-tld-1.goflexhome. The system starts to...
View ArticleNo autoboot display (no replies)
After switching on my GoFlex Home, the U-Boot msg comes up but there is no ' Stop autoboot in x secs' msg so I can't break in. Is there a variable that sets this?
View ArticleMulti purpose uBoot (1 reply)
Is there a single uBoot which I can use to boot Debian, ArchLinux, OpenWrt and FreeBSD? I would like to have this range of options if possible. I understand the special edition...
View ArticleNSA310 not booting after flashing 2017.07 U-Boot Kirkwood (1 reply)
Hi All! First of all thanks to bodhi for all your work! Today I tried flashing Uboot to my NSA310 by following instructions from https://forum.doozan.com/read.php?3,12381 Everything went well until I...
View Article