GoFlexHome RIP (4 replies)
After attempting to update the environment on my GoFlexHome today I ran reboot from the Debian command prompt hoping to see the new environment when it restarted.... but it never did...the green LED...
View ArticleSeagate Personal Cloud (1 reply)
Has anyone tried to update U-Boot on a Seagate Personal Cloud?...
View ArticlePogoplug eo2 not showing in router (1 reply)
Hello all, I've browsed this forum a few times when I ran into issues with my pogo plug about a year ago, and now I need your help again. Recently I tried to gain access to my device through the...
View ArticlePogoplug V4 not booting (1 reply)
Greetings, Please help.... apparently I've made my Pogoplug V4 unable to boot. Front Led always off all the time, not blinking at all, not even the green one. Serial connection status are connected,...
View Articlegoflex randomly stops showing files (2 replies)
My seagate goflex home works "some" of the time. if it loses wifi connectivity or has to be restarted it will often startup without any files in the file system. after restarting several times in a...
View ArticleQuestion about 2017.07 U-Boot Kirkwood for Dockstar (1 reply)
I have a dockstar and had an older version of your uboot - I assume from 2011. I installed this version. All steps worked including the writing of the environment except setting ethaddr...
View Articlegoogle customer service (no replies)
We are providing best service to our customer and our team serves satisfactory service to our customer. Contact with our team Google customer service
View ArticleInstalling new U-Boot for Pogoplug V3 - from Arch u-boot (15 replies)
I hope this is the right place to post this - I'm mostly concerned about U-Boot issues... I have an old Pogo-Classic (B01) running ArchLinux that I installed years ago. It was my first Pogoplug...
View ArticlePogoplug V4 Troubleshooting Help (1 reply)
I'm having issues with my Pogoplug not always booting and I would appreciate some help/advice on the boot issues I'm having. It will not boot at all with the usb removed, just a green flashing light,...
View ArticleNot the correct encoding? (1 reply)
Hi I an using a CP2102 USB to UART bridge, and it connects correctly. I am using "serial" on my mac, but something is wrong with the encoding (?) as I get the following: U-B⎺⎺├ 2011.12 (F␊␉ 20 2012 -...
View ArticleWrong U-boot Envs on Pogo Pro ? (no replies)
Hi Folks, As i tried to install LEDE into the flash of my POGO Pro, i messed up my Uboot ENvs and cannot boot into debian anymore. At the moment, i can only get access to my pogo via serial cable. Her...
View ArticleProblem booting with 2017.07 U-Boot Kirkwood NSA325 (1 reply)
I have lost my serial connection just before 8. Flashing default u-boot envs image (if you are upgrading from 2016.05-tld-1 u-boot, you can skip this step 8). the U-Boot was flashed successfully to...
View ArticleNeed help with a brand new Pogoplug Mobile (no replies)
I actually have two of these with the same issue. These are brand new out of box Pogoplug Mobile devices that I finally had time to open and try and set up, hoping to enable SSH and eventually install...
View ArticleAkitio Mycloud Duo with 2015.10 U-Boot for Pogoplug V3 (OXNAS OX820) (2 replies)
Hello please help. I try to flash new u-boot on Iconbit I-STOR IS608 clone of Akitio Mycloud Duo . reboot after success flash u-boot: U-Boot SPL 2013.10 (Apr 27 2014 - 19:08:27) Boot device: NAND...
View ArticleUpdate uboot from 2016.05 (no replies)
A list of only 6 checked items, that is what I need to do: ☐ Check /etc/fw_env.config and /proc/mtd ☐ Set ethaddr ☑ Dump NAND mtd0 and Save envs ☑ No bad block ──────────── ☑ Extract the archive ☑...
View ArticleUse uEnv.txt for Testing (no replies)
My Pogo server have run on the NFS for more than 1 year, and I never worry about the lifespan of the SD card. An old IDE hard disk is attached to the Openwrt router by USB 2.0 and provide a stable...
View ArticleU-Boot for PogoPlug E01 (no replies)
The Pogoplug E01 is essentially a re-branded GlobalScale Sheevaplug even sharing the 003-SPL1001 model number. The most apparent difference is that the Pogoplug E01 has only 256MB of memory where the...
View ArticleNo serial output (no replies)
I gave up on one of my GoFlex Home docks a few months ago because nothing was being output to the serial connection... Now after revisiting it, I see that the green LED has stopped flashing and become...
View ArticleFreeBSD adventure continues (no replies)
I managed to get one GoFlexHome dock to boot up FreeBSD but in the process of tidying up the environment managed to brick it... Still looking at trying to JTAG it, but getting nowhere. I have another...
View ArticleHacking into a stock GoFlexHome unit (no replies)
I've just acquired another GoFlexHome unit which is still running the stock software. What's the most straightforward way of getting a new uBoot onto it? I don't really want to follow the Arch Linux...
View Article