Netconsole help (2 replies)
I would like to use netconsole to monitor the boot process on my GoFlexHome unit but am unsure as to how to run it. I've read:- https://forum.doozan.com/read.php?3,14 but am unclear as to how to run...
View ArticleDebian and Arch Linux rootfs differences (no replies)
I created an Arch Linux bootable USB stick for my GoFlexHome unit the other day and it only required the rootfs to be extracted and was bootable. In contrast a number of additional steps are needed...
View ArticleGoFlexHome u-boot 2017-07-tld-1 (3 replies)
I'm trying to update u-boot on a GoFlexHome dock according to instructions here:- https://forum.doozan.com/read.php?3,12381 I've downloaded uboot.2017.07-tld-1.goflexhome.bodhi.tar from...
View ArticleGoFlexHome (2 replies)
So I feel not smart, and specifically, that special kind that comes from trying to be smart. Like when you try to outsmart your car to get it to let you lock it with it running only to later find the...
View ArticleSaving GoFlexHome stock firmware (no replies)
I've just acquired another GoFlexHome dock and wondered if there is any way to save the stock firmware before I start installing my own U-Boot...
View ArticlePogoplug Pro OXNAS with entirely corrupt NAND (no replies)
I found a Pogoplug Pro that was destined for the trash bin. NAND appears to be completely fried on the device. I have serial console working on another device, so I'm sure I can get it working here...
View ArticleMarvell Dreamplug U-Boot-2017.07-tld-1 (1 reply)
This is the official released version for Marvell Dreamplug U-Boot-2017.07-tld-1. I am writing the installation instruction for this u-boot. In the mean time, here is the download link. Download at...
View ArticleUnbrick a Pogoplug Pro (v3/OXNAS?) (3 replies)
Greetings, After much success with my Pogoplug v4/mobile, I figured I would try to get my larger v3/Oxnas boards working. I seem to have bricked one right out of the gate. I have a sinking suspicion I...
View ArticleTesting for Marvell Dreamplug U-Boot-2017.07-tld-1 (no replies)
I used kwboot with the latest kernel and rootfs. Linux debian 4.13.5-kirkwood-tld-1 Debian-4.12.1-kirkwood-tld-1-rootfs uboot.2017.07-tld-1.dreamplug Which produces the already known. [ 22.738932]...
View Articlestock pogoV4: fw_printenv gives "Bad CRC: using default environment" (1 reply)
I apologize because I'm pretty sure I've dealt with this issue before, but I can't remember the (probably trivial) way around it: Stock PogoPlug V4, I managed to enable SSH via serial connection and...
View Articlearmada 370 (88f6710) mainline uboot support (3 replies)
Hi bodhi, I have a device use the armada 370 soc,but there is no mainline uboot support.And I found someone make some patch to support the armada 370 see:...
View Article*** ERROR: `ethaddr' not set (1 reply)
I wanted to change the IP address of my GoFlexHome unit, so I ran:- fw_setenv ipaddr 192.168.1.23 at a Debian command prompt. On reboot and stopping U-Boot and trying tftp xxxxxx yyyyy, I got an error...
View Articlehelp install u-boot on lenovo ix2-ng (1 reply)
my storage is broken I accidentally overwritten the bootloader and looking for a recovery method help who can
View ArticleNSA325v2 u-boot installation problem (4 replies)
Hi guys! Yesterday night I tried to update u-boot on my NSA325v2 with stock firmware. I followed all of the instructions until the step 8.b and I forgot to do the step 8.c: fw_printenv >...
View ArticleFrom stock to uboot.2017.07-tld-1.goflexhome.mtd0.kwb (1 reply)
If I want to install uboot.2017.07-tld-1.goflexhome.mtd0.kwb on a stock Seagate GoFlexHome unit, do I first have to go through the process described here...
View ArticleBeaglebone support (1 reply)
Does anyone know of a U-Boot for Beaglebone http://beagleboard.org/ ?
View ArticleFreeBSD on GoFlexHome (3 replies)
After many months of trying and thanks to the patience of bodhi I have got this far:- U-Boot 2017.05-tld-2 (Jul 26 2017 - 02:37:42 -0700) Seagate GoFlex Home SoC: Kirkwood 88F6281_A1 DRAM: 128 MiB...
View ArticleProblem with 2017.07 U-Boot for SheevaPlug (no replies)
After installing the new 2017.07 U-Boot on a SheevaPlug I was having trouble booting and I discovered the issue is a missing "load" command. Sheevaplug> load usb 0:1 $load_uimage_addr /boot/uImage...
View ArticleuEnv.txt (no replies)
How do you get U-Boot to read uEnv.txt while booting? Are there some environment parameters which should be set for this to take place?
View Article** File not found /boot/uImage ** (1 reply)
I just updated my U-Boot to 2017.07-tld-1 (Oct 24 2017 - 22:32:36 -0700) and I'm occasionally getting the following (from netconsole):starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices......
View Article