HOW2: Repair Pogo E02 with Raspberry PI (JTAG) and OpenOCD (4 replies)
I startet my new projekt to repair a broken Pogo E02 (damaged bootloader - mtd0) with a Raspberry PI used as JTAG Interface. see here my final solution:...
View ArticleDockstar requires uboot cli command to boot from usb stick (7 replies)
I got my Dockstar upgraded with the new uboot and the new Jessie from a usb stick. I have a serial cable connected to monitor the boot process. The dockstar goes to the uboot prompt when I power it up...
View Articlelinux- Headers seem to be old version (2 replies)
Bodhi, I've upgraded to Arch 4.0,2 on my Pogo V4 and everything runs fine except I went to compile a Wifi module and it errored out because it couldn;t find the correct Linux headers where they should...
View ArticlePogoplug Pro/Debian phenomenon when SATA-booting (4 replies)
Two Pogoplug Pros here with numerical names based on IP address reservation: 102: OpenWRT internally 104: uboot barely made it on In both cases, they boot the recent Debian USB stick (those are...
View Articlepogo e02 bricked ? (1 reply)
hi guys, i was trying to install debian on my pogoplug e02 but i ended up with a brick after a power off. ETH led is blinking but i can't access with SSH anymore. I followed ]this tutorial and the...
View Articlecannot change SSH password (6 replies)
I am having a similar issue like mentioned here, although mine is that I cannot _change_ my SSH password ... I have a PogoplugPro, that I got used a couple of years ago. I was playing around with it...
View ArticleuBoot update script - PogoplugPro ... ? (3 replies)
Before I brick my device - does the uBoot update script mentioned here work for a PogoplugPro? When I run it, it explicitely says: This installer will only work on the following devices: Seagate...
View Articlestep by step of how to install Debian on stock PogoplugPro (20 replies)
I am reading posts here about installing Debian with the latest rootfs and the latest uBoot and I am jumping around between references to topics and I am getting utterly confused. Where exactly do I...
View Articleserial cable - parts (1 reply)
I purchased this (and this) on eBay. I am all thumbs and just wanted to make sure that this would make a good serial cable for my Pogoplug, before I plug it in and fry my board ... Thanks!
View ArticlePogo V3 Oxnas Booting with SATA and USB (1 reply)
Hi Sorry for the delay in replying to your suggestion. I tried your suggestion and some other different things in the U-Boot environment to try and get the Pogoplug to boot Debian from a Sata disk...
View ArticleIDE read: device 0 not ready with U-Boot 2014.07-tld-2 (11 replies)
Hello, I have a boot problem with a 6G/s SSD. (1.5 G/s WD drive works fine) U-Boot 2014.07-tld-2 (Sep 20 2014 - 00:58:11) Seagate GoFlex Net gcc (Debian 4.6.3-14) 4.6.3 GNU ld (GNU Binutils for...
View Articlecorrect uEnv.txt for recovering pogoplug v4 mobile environment (1 reply)
I've successfully updated U-Boot on it and I'm using bodhi's rootfs. A fiew days ago I noticed that I have a limited environment so I changed it via fw_setenv like on other devices but it doesn't came...
View ArticleNetconsole performance (2 replies)
I have a pogoplug e02 running: U-Boot 2014.07-tld-2 (Sep 20 2014 - 00:52:18) Net console lags, when I type in ? it takes 30-45 seconds to display. In the serial console when booting it says: host...
View ArticleIs possible to chainload Bodhi's Uboot from stock Uboot? (8 replies)
I did an automated installer script to install debian and OMV into Zyxel NAS boxes from nsa310 onwards. For nsa325 and the v2 it's not possible to disable reliably the watchdog without flashing your...
View ArticleNeed help rescue my Goflex home (2 replies)
I installed Arch Linux on my GFH years ago, and it worked fine until a few weeks ago when I did a pacman update. Now I can't ssh into it, but could still ping it. I tried creating an USB from this...
View ArticleMarvell Reference Manual - Functional Specs for 88F6282 (2 replies)
All, I'm in need to learn a certain aspect of this SoC that should be in Marvell Function Specifications for the 88F6282 SoC (found in Zyxel NSA325 and other NAS brands). It took Marvell a while to...
View Articlereading GPIO registers in RAM (2 replies)
Following a lead in a message left by the ALARM dev of the kirkwood kernel/u-boot, I would need some help to read GPIO registers in RAM so I can disable nsa325 watchdog with a mw from stock u-boot....
View ArticleFujitsu Q700/QNAP TS-219 - dead UART no console output (4 replies)
Hi, some time ago I experimented with u-boot env settings and reflashing and i ended up with bricked NAS. Since my last write command and reboot there is no output on console, just black screen. I...
View ArticleChainload U-Boot on NSA325v2 from bodhi's u-boot (1 reply)
Hi, I have U-Boot 2014.07-tld-3 on nand. I compiled another version of u-boot (which I know it works because I already tried flashing). I'm trying to chainloading it from 2014.07-tld-3 version :...
View ArticlePogoV4 not booting and no ethernet connection (4 replies)
HI, Been trying this for 2 days followed instructions on http://blog.qnology.com/2014/07/hacking-pogoplug-v4-series-4-and-mobile.html never did work right..not sure what went wrong and where to go...
View Article