Changing boot sequence for making stubborn SSD (bad firmware?) boot. (no...
Hi Bodhi! It's me again, with that annoying Transcend SSD. The problem is, that this SSD doesn't work reliably after the IDE reset. Sometimes it's working and some times it's timing out. This is not...
View ArticleHow to convert zImage to Image for GoFLEX Home (1 reply)
Bodhi, Looks like ARCH Linux ARM (ALARM) has this ArchLinuxARM-armv5-latest.tar.gz and this ArchLinuxARM-kirkwood-latest.tar.gz. I am not sure what are differences between the two. I use the later one...
View ArticleNAND errors - BAD eraseblocks - how to fix it? NSA310, Archlinux...
Hello members. This is part of my dmesg: [ 12.438580] Bad eraseblock 0 at 0x000000000000 [ 12.443121] Bad eraseblock 1 at 0x000000020000 [ 12.447626] Bad eraseblock 2 at 0x000000040000 [ 12.452143]...
View Articlemainline kirkwood uboot (no replies)
Sorry for what may be taken as a political first question ... Is there a reason why the kirkwood uboot isn't mainlined on the denx site, instead maintained by bodhi? Just thinking if mainlined, would...
View ArticleWhat version of Rescue am I running? (no replies)
I recently pulled my GoFlex Home out of the closet to start working with it again. It's running an installation of the rescue provided on these forums, but I installed it so long ago that I can't...
View ArticleNeed help with a brand new Pogoplug Mobile (4 replies)
I actually have two of these with the same issue. These are brand new out of box Pogoplug Mobile devices that I finally had time to open and try and set up, hoping to enable SSH and eventually install...
View ArticleIssues with Cisco ON100 booting (6 replies)
Hi, First post here so sorry if I seem vague. I've been working on getting OpenWRT running on my Cisco ON100 which is a Marvell Kirkwood based device. I'll preface this by saying my experience with...
View ArticleNSA325 uboot does not detect hdd (no replies)
hello, I am trying to configure a NSA325 however it does not seem to be able to detect my sata drives (hdd). I plugged a HDD in the left slot (but on the right slot it does not detect it either...)...
View ArticlePogoplug 4 uboot update won't boot (2 replies)
Bodhi , I have a Pogo4 with Arch updated Uboot and Arch and now it won't boot with SD card. I have an old flash drive with Arch on it and it will boot from that but not from the SD card with the...
View ArticleOpenWrt on GoFlex Home (no replies)
Apparently OpenWrt can be installed on a GoFlex Home unit.... Does anyone have experience of this and pointers about how to do this?
View ArticleHow to unbrick GoFlex Home? (1 reply)
I have a GoFlex Home that won't boot. I've connected it to a terminal via a USB to UART, but I can't get any output from the device. (I've tested that the CP2102 interface works, because messing with...
View ArticleuBoot version (2 replies)
How do I identify the uBoot version I have installed on my GoFlex Home unit?
View ArticleReading uEnv.txt from uBoot prompt (2 replies)
How do I load environment variables from uEnv.txt once I have booted up from kwboot and am at the uBoot prompt?
View Articlekwboot (2 replies)
Apologies if this off-topic, but I thought someone here might be able to give me some insight on my problem... I've been trying to get kwboot working on FreeBSD for a while without any success and...
View Articlehttps://shopdumps101.com/Sell dumps, Shop dumps 101, 201,dumps with pin, Atm...
https://shopdumps101.com/sell dumps,dumps with pin track1&2,sell dumps online. valid rate 98%.....!!!!! Selling dumps - shop dumps - dumps with pin - sell dumps online Contact me - ICQ : 690616620...
View ArticleHacking into a stock GoFlexHome unit (24 replies)
I've just acquired another GoFlexHome unit which is still running the stock software. What's the most straightforward way of getting a new uBoot onto it? I don't really want to follow the Arch Linux...
View ArticleHelp Pogoplug e02 uboot won't boot (4 replies)
here is console ： U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700) Pogo E02 SoC: Kirkwood 88F6281_A0 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net:...
View ArticleNSA320 u-boot installation problem 1 (3 replies)
I'm trying to update a couple of NSA320 servers and find that the "environlent" files give me errors when it try to un-tar them. Are the default environment (without specific entries ethaddr etc.)...
View ArticlePogo V4 - 2017.07 U-Boot Kirkwood installation problem (1 reply)
So I installed -according to me- the latest uboot (uboot.2017.07-tld-1.pogo_v4.bodhi + uboot.2016.05-tld-1.environment.bodhi) and a pretty new debian kirkwood...
View ArticleAnyone has the link to show me the process of update in a pogoplug pro? (2...
Hi , i am a little lost here. my device say model:pogoplug pro fccid:vuipogoplug what process i have to follow to update uboot ? Thanks in advance Martin
View Article
