Hi,
I tried to create a wheezy USB stick on my 'old' squeeze dockstar. Now I can only boot into pogo - w/o really knowing why.
1) started the wheezy installation which updated the uboot
2) failed to create wheezy with Kernel to old message
3) found that neither internal debian squeeze nor usb squeeze boots any longer - both fail with unsupported machine id error
4) interrupted boot, printenv shows "arcNumber=2097"
5) tried to install improved rescue system from pogo - which refuses to update the boot partition, reasonable
6) tried to install rescue system on second dockstar - as the upgrade of uboot happend, too, its not stuck, too .-)
7) tried to install squeeze again thinking that it might install an older uboot - which it didn't :-)
So now I'm stuck w/o good ideas how to recover the boxes and continue. I can only boot into pogo at this point in time - serial cable is available.
Help is really appreciated.
Fritz!
I tried to create a wheezy USB stick on my 'old' squeeze dockstar. Now I can only boot into pogo - w/o really knowing why.
1) started the wheezy installation which updated the uboot
2) failed to create wheezy with Kernel to old message
3) found that neither internal debian squeeze nor usb squeeze boots any longer - both fail with unsupported machine id error
4) interrupted boot, printenv shows "arcNumber=2097"
5) tried to install improved rescue system from pogo - which refuses to update the boot partition, reasonable
6) tried to install rescue system on second dockstar - as the upgrade of uboot happend, too, its not stuck, too .-)
7) tried to install squeeze again thinking that it might install an older uboot - which it didn't :-)
So now I'm stuck w/o good ideas how to recover the boxes and continue. I can only boot into pogo at this point in time - serial cable is available.
Help is really appreciated.
Fritz!
unrecognized/unsupported machine ID (r1 = 0x00000bb6). Available machine support: ID (hex) NAME 00000690 Marvell DB-88F6281-BP Development Board 00000691 Marvell RD-88F6192-NAS Development Board 00000692 Marvell RD-88F6281 Reference Board 0000078c Marvell 88F6281 GTW GE Board 00000a76 Marvell eSATA SheevaPlug Reference Board 00000831 Marvell SheevaPlug Reference Board 00000a63 Marvell GuruPlug Reference Board 0000085b QNAP TS-119/TS-219 000009c6 QNAP TS-41x 00000b44 Marvell OpenRD Ultimate Board 00000939 Marvell OpenRD Client Board 00000915 Marvell OpenRD Base Board 00000b1e HP t5325 Thin Client Please check your kernel config and/or bootloader.
fw_printenv ethact=egiga0 bootdelay=3 baudrate=115200 mainlineLinux=yes console=ttyS0,115200 led_init=green blinking led_exit=green off led_error=orange blinking mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) mtdids=nand0=orion_nand partition=nand0,2 stdin=serial stdout=serial stderr=serial rescue_installed=0 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_list=1 2 3 4 usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_init=run usb_scan usb_device=0:1 usb_root=/dev/sda1 usb_rootfstype=ext2 usb_rootdelay=10 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset ethaddr=00:10:75:1A:5A:76 arcNumber=2097