After update to u-boot 2016.05-tld-1 on NSA325v1 is not booting (1 reply)

Hi there,

I've been reading here for a long time and I dared yesterday to change the u-boot from 1.1.4 on one of my two NSA325v1. So I used a serial connection to my Mac and updated the u-boot as described in this article: http://forum.doozan.com/read.php?3,12381 With nandwrite the expected output was right:

Writing data to block 0 at offset 0x0 
Writing data to block 1 at offset 0x20000 
Writing data to block 2 at offset 0x40000 
Writing data to block 3 at offset 0x60000

But now I'm in trouble at step B, after a reboot the system shows the following:

U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:48:40 -0700)
ZyXEL NSA325 2-Bay Power Media Server

SoC:   Kirkwood 88F6282_A1
DRAM:  512 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
MV88E1318 PHY initialized on egiga0
Hit any key to stop autoboot:  0
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found

Partition Map for USB device 0  --   Partition Type: EFI

Part    Start LBA       End LBA         Name
        Attributes
        Type GUID
        Partition GUID
  1     0x00000022      0x0079b15e      "Microsoft basic data"
        attrs:  0x0000000000000000
        type:   ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
        guid:   c1d82d0b-dafe-47ba-a20a-7c116fb4c695
loading envs from usb 0 ...
reading /boot/uEnv.txt
** Unable to read file /boot/uEnv.txt **
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
Wrong Image Format for bootm command
Error occured, error code = 112
ERROR: can't get kernel image!
stopping USB..

Reset IDE: Bus 0: OK Bus 1: OK
  Device 0: Model: WDC WD10EADS-11M2B2  Firm: 80.00A80 Ser#:  WD-WCAV5D830190
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
  Device 1: Model: Hitachi HDS721010CLA332  Firm: JP4OA3EA Ser#: JP2911HD188TZC
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
** File not found /boot/uImage **
** File not found /boot/uInitrd **
Wrong Image Format for bootm command
Error occured, error code = 112
ERROR: can't get kernel image!
resetting ...

So - what where my configs (with the old u-boot from marvel):
cat /etc/fw_env.config

 
# Configuration file for fw_(printenv/saveenv) utility.
# Up to two entries are valid, in this case the redundand
# environment sector is assumed present.
# Notice, that the "Number of sectors" is ignored on NOR.

# MTD device name       Device offset   Env. size       Flash sector size       Number of sectors
# NAND example
/dev/mtd1		0x0000		0x20000		0x20000			4

cat /proc/mtd

 
dev:    size   erasesize  name
mtd0: 00100000 00020000 "uboot"
mtd1: 00080000 00020000 "uboot_env"
mtd2: 00080000 00020000 "key_store"
mtd3: 00080000 00020000 "info"
mtd4: 00a00000 00020000 "etc"
mtd5: 00a00000 00020000 "kernel_1"
mtd6: 02fc0000 00020000 "rootfs1"
mtd7: 00a00000 00020000 "kernel_2"
mtd8: 02fc0000 00020000 "rootfs2"

I'm not shure how I'm flashing now the default u-boot envs into the image. Which are these envs? Which files must located where? Or I'm totally wrong? So it would be great if someone could help me and lead me to the right way ;-)

Kind regards, machnetz