NSA310 with uboot.2015.10-tld-1 HD detection (4 replies)

Hi bodhi!

Thanks for your great work!

I finally took the plunge and flashed the uboot.2015.10-tld-1 on my NSA310. I hade a couple of bad blocks on
00040000
00060000
but I did some reading and decided to take my chances on 'nand scrub 0x0 0x80000' and it worked. However, after reboot it seems that I cannot detect the SATA SSD disk properly anymore. I get only garbled description and wrong specs ending in SSD unreadable. It is a 16GB SSD that is formatted in three partitions. Partition 1 is boot in ext2 with uImage & Uinitrd. Partition 2 empty ext4. Partition 3 ext4 labeled "rootfs" with root on it.

Printeenv:

arcNumber=4022
baudrate=115200
bootcmd=run bootcmd_uenv; run bootcmd_usb; usb stop; run bootcmd_sata; reset
bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot
bootdelay=10
console=ttyS0,115200
device=0:1
ethact=egiga0
ethaddr=b6:d0:5e:0f:a1:17
led_error=orange blinking
led_exit=green off
led_init=green blinking
machid=118f
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)
partition=nand0,2
rootdelay=10
rootfstype=ext2
sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
sata_init=ide reset
sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage
sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd
sata_root=/dev/sda3
set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
stderr=serial
stdin=serial
stdout=serial
uenv_import=echo importing envs ...; env import -t 0x810000
uenv_load=usb start; setenv uenv_loaded 0; for devtype in usb; do for disknum in 0; do run uenv_read_disk; done; done
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x810000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if $devtype part $disknum; then run uenv_read; fi
usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_init=usb start
usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage
usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd
usb_root=/dev/sda1

Bootlog:

U-Boot 2015.10-tld-1 (Nov 06 2015 - 16:19:43 -0800)
ZyXEL NSA310 1-Bay Power Media Server


SoC:   Kirkwood 88F6281_A1
DRAM:  256 MiB (ECC not enabled)
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
PHY reset timed out
MV88E1318 PHY initialized on egiga0
Hit any key to stop autoboot:  0
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found

no USB devices available
** Bad device usb 0 **
** Bad device usb 0 **
Wrong Image Format for bootm command
Error occured, error code = 112
ERROR: can't get kernel image!
stopping USB..

Reset IDE: Bus 0: OK Bus 1: not available
  Device 0: Model: ?▒?▒?▒?▒?▒?▒?▒?▒?▒?▒?▒?▒?▒?▒?▒?▒?▒?▒?▒?▒ Firm: ?▒?▒?▒?▒ Ser#: ?▒?▒?▒?▒?▒?▒?▒?▒?▒?▒
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 427923841.5 MB = 417894.3 GB (4611474908973580287 x 512)
IDE read: device 0 not ready
IDE read: device 0 not ready
** No partition table - ide 0 **
** No partition table - ide 0 **
Wrong Image Format for bootm command
Error occured, error code = 112
ERROR: can't get kernel image!
resetting ...