hello every one
i have bought my PogoPlug E02 black one one week ago and yesterday i tried to install uboot (/install_uboot_mtd0.sh) and then to install Arch Linux ARM but unfortunallty i go error message (Installation cancelled.) then i forced the installation with (--no-uboot-check ) but again i go this message (uBoot could not be downloaded, or the MD5 does not match.)
the prompet of the switched from bash to pogoplug and i have tried to install again but with no result.
then i found one topic (dont remeber it now ) which contains some steps how to remove some data from flash and the earse !!!! actully i'm not fimilar with these command in unix but i tried it.
now i cant access it via ssh but can access using serial connection , below is the messages i got , it stops at this line
then start the boot over again
now i need to know how to fix this issue to run ARM on this box or to return to the default pogoplug image.
Waiting for your help
thanks
i have bought my PogoPlug E02 black one one week ago and yesterday i tried to install uboot (/install_uboot_mtd0.sh) and then to install Arch Linux ARM but unfortunallty i go error message (Installation cancelled.) then i forced the installation with (--no-uboot-check ) but again i go this message (uBoot could not be downloaded, or the MD5 does not match.)
the prompet of the switched from bash to pogoplug and i have tried to install again but with no result.
then i found one topic (dont remeber it now ) which contains some steps how to remove some data from flash and the earse !!!! actully i'm not fimilar with these command in unix but i tried it.
now i cant access it via ssh but can access using serial connection , below is the messages i got , it stops at this line
Scheduling watchdog timeout to force reboot...
then start the boot over again
U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV2 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x200000 Reading data from 0x2ff800 -- 100% complete. 2097152 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2010-10-19 23:05:02 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1979140 Bytes = 1.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux............................................................................................................................ done, booting the kernel. [ 0.000000] Linux version 2.6.22.18 (bdietrich@buildman) (gcc version 4.2.1) #81 Tue Oct 19 16:05:00 PDT 2010 [ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177 [ 0.000000] Machine: Feroceon-KW [ 0.000000] Using UBoot passing parameters structure [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] CPU0: D VIVT write-back cache [ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] Built 1 zonelists. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro [ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes) [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.010000] Memory: 256MB 0MB 0MB 0MB = 256MB total [ 0.010000] Memory: 255872KB available (3592K code, 253K data, 124K init) [ 0.250000] Mount-cache hash table entries: 512 [ 0.250000] CPU: Testing write buffer coherency: ok [ 0.250000] NET: Registered protocol family 16 [ 0.250000] [ 0.250000] CPU Interface [ 0.250000] ------------- [ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB [ 0.250000] SDRAM_CS1 ....disable [ 0.250000] SDRAM_CS2 ....disable [ 0.250000] SDRAM_CS3 ....disable [ 0.250000] PEX0_MEM ....base e8000000, size 128MB [ 0.250000] PEX0_IO ....base f2000000, size 1MB [ 0.250000] INTER_REGS ....base f1000000, size 1MB [ 0.250000] NFLASH_CS ....base fa000000, size 2MB [ 0.250000] SPI_CS ....base f4000000, size 16MB [ 0.250000] BOOT_ROM_CS ....no such [ 0.250000] DEV_BOOTCS ....no such [ 0.250000] CRYPT_ENG ....base f0000000, size 2MB [ 0.250000] [ 0.250000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE [ 0.250000] [ 0.250000] Detected Tclk 200000000 and SysClk 400000000 [ 0.250000] MV Buttons Device Load [ 0.250000] Marvell USB EHCI Host controller #0: c0652600 [ 0.750000] PEX0 interface detected no Link. [ 0.750000] PCI: bus0: Fast back to back transfers enabled [ 0.750000] SCSI subsystem initialized [ 0.750000] usbcore: registered new interface driver usbfs [ 0.750000] usbcore: registered new interface driver hub [ 0.750000] usbcore: registered new device driver usb [ 0.750000] NET: Registered protocol family 2 [ 0.760000] Time: kw_clocksource clocksource has been installed. [ 0.850000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.850000] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.850000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [ 0.850000] TCP: Hash tables configured (established 8192 bind 8192) [ 0.850000] TCP reno registered [ 0.880000] RTC has been updated!!! [ 0.880000] RTC registered [ 0.880000] Use the XOR engines (acceleration) for enhancing the following functions: [ 0.880000] o RAID 5 Xor calculation [ 0.880000] o kernel memcpy [ 0.880000] o kenrel memzero [ 0.880000] Number of XOR engines to use: 4 [ 0.880000] cesadev_init(c00117b0) [ 0.880000] mvCesaInit: sessions=640, queue=64, pSram=f0000000 [ 0.880000] MV Buttons Driver Load [ 0.880000] squashfs: version 3.3 (2007/10/31) Phillip Lougher [ 0.880000] squashfs: LZMA suppport for slax.org by jro [ 0.880000] JFFS2 version 2.2. (NAND) أ‚آ© 2001-2006 Red Hat, Inc. [ 0.880000] io scheduler noop registered [ 0.880000] io scheduler anticipatory registered (default) [ 0.900000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 0.900000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 0.910000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize [ 0.920000] Loading Marvell Ethernet Driver: [ 0.920000] o Cached descriptors in DRAM [ 0.920000] o DRAM SW cache-coherency [ 0.930000] o Single RX Queue support - ETH_DEF_RXQ=0 [ 0.930000] o Single TX Queue support - ETH_DEF_TXQ=0 [ 0.940000] o TCP segmentation offload enabled [ 0.940000] o Receive checksum offload enabled [ 0.950000] o Transmit checksum offload enabled [ 0.950000] o Network Fast Processing (Routing) supported [ 0.960000] o Driver ERROR statistics enabled [ 0.960000] o Driver INFO statistics enabled [ 0.970000] o Proc tool API enabled [ 0.970000] o Rx descripors: q0=128 [ 0.970000] o Tx descripors: q0=532 [ 0.980000] o Loading network interface(s): [ 0.990000] o eth0, ifindex = 1, GbE port = 0 [ 0.990000] o eth1, ifindex = 2, GbE port = 1 [ 1.000000] [ 1.000000] mvFpRuleDb (cfdf6000): 2048 entries, 8192 bytes [ 1.000000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI [ 1.010000] Copyright (c) 1999-2006 Intel Corporation. [ 1.020000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI [ 1.020000] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.030000] [ 1.030000] Warning Sata is Powered Off [ 1.030000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ [ 1.040000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit) [ 1.050000] Scanning device for bad blocks [ 1.100000] Using static partition definition [ 1.110000] Creating 4 MTD partitions on "nand_mtd": [ 1.110000] 0x00000000-0x00100000 : "u-boot" [ 1.120000] 0x00100000-0x00500000 : "uImage" [ 1.120000] 0x00500000-0x02500000 : "root" [ 1.130000] 0x02500000-0x08000000 : "data" [ 1.130000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI [ 1.140000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 [ 1.180000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 [ 1.200000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 1.200000] usb usb1: configuration #1 chosen from 1 choice [ 1.210000] hub 1-0:1.0: USB hub found [ 1.210000] hub 1-0:1.0: 1 port detected [ 1.330000] USB Universal Host Controller Interface driver v3.0 [ 1.610000] usb 1-1: new high speed USB device using ehci_marvell and address 2 [ 1.760000] usb 1-1: configuration #1 chosen from 1 choice [ 1.760000] hub 1-1:1.0: USB hub found [ 1.770000] hub 1-1:1.0: 4 ports detected [ 1.880000] usbcore: registered new interface driver usblp [ 1.880000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver [ 1.890000] Initializing USB Mass Storage driver... [ 1.890000] usbcore: registered new interface driver usb-storage [ 1.900000] USB Mass Storage support registered. [ 1.910000] mice: PS/2 mouse device common for all mice [ 1.910000] i2c /dev entries driver [ 1.910000] Linux telephony interface: v1.00 [ 1.920000] md: linear personality registered for level -1 [ 1.920000] md: raid0 personality registered for level 0 [ 1.930000] md: raid1 personality registered for level 1 [ 2.100000] raid6: int32x1 97 MB/s [ 2.270000] raid6: int32x2 114 MB/s [ 2.440000] raid6: int32x4 122 MB/s [ 2.610000] raid6: int32x8 110 MB/s [ 2.610000] raid6: using algorithm int32x4 (122 MB/s) [ 2.610000] md: raid6 personality registered for level 6 [ 2.620000] md: raid5 personality registered for level 5 [ 2.620000] md: raid4 personality registered for level 4 [ 2.630000] raid5: measuring checksumming speed [ 2.680000] arm4regs : 1084.000 MB/sec [ 2.730000] 8regs : 754.800 MB/sec [ 2.780000] 32regs : 900.000 MB/sec [ 2.780000] raid5: using function: arm4regs (1084.000 MB/sec) [ 2.790000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com [ 2.790000] dm_crypt using the OCF package. [ 2.800000] sdhci: Secure Digital Host Controller Interface driver [ 2.800000] sdhci: Copyright(c) Pierre Ossman [ 2.810000] usbcore: registered new interface driver usbhid [ 2.810000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 2.820000] TCP cubic registered [ 2.820000] NET: Registered protocol family 1 [ 2.830000] NET: Registered protocol family 17 [ 2.830000] md: Autodetecting RAID arrays. [ 2.840000] md: autorun ... [ 2.840000] md: ... autorun DONE. [ 3.070000] VFS: Mounted root (jffs2 filesystem) readonly. [ 3.070000] Freeing init memory: 124K [ 3.070000] Warning: unable to open an initial console. [ 3.080000] Kernel panic - not syncing: No init found. Try passing init= option to kernel. [ 3.090000] Scheduling watchdog timeout to force reboot... U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV2 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x200000 Reading data from 0x2ff800 -- 100% complete. 2097152 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2010-10-19 23:05:02 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1979140 Bytes = 1.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux............................................................................................................................ done, booting the kernel. [ 0.000000] Linux version 2.6.22.18 (bdietrich@buildman) (gcc version 4.2.1) #81 Tue Oct 19 16:05:00 PDT 2010 [ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177 [ 0.000000] Machine: Feroceon-KW [ 0.000000] Using UBoot passing parameters structure [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] CPU0: D VIVT write-back cache [ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] Built 1 zonelists. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro [ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes) [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.010000] Memory: 256MB 0MB 0MB 0MB = 256MB total [ 0.010000] Memory: 255872KB available (3592K code, 253K data, 124K init) [ 0.250000] Mount-cache hash table entries: 512 [ 0.250000] CPU: Testing write buffer coherency: ok [ 0.250000] NET: Registered protocol family 16 [ 0.250000] [ 0.250000] CPU Interface [ 0.250000] ------------- [ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB [ 0.250000] SDRAM_CS1 ....disable [ 0.250000] SDRAM_CS2 ....disable [ 0.250000] SDRAM_CS3 ....disable [ 0.250000] PEX0_MEM ....base e8000000, size 128MB [ 0.250000] PEX0_IO ....base f2000000, size 1MB [ 0.250000] INTER_REGS ....base f1000000, size 1MB [ 0.250000] NFLASH_CS ....base fa000000, size 2MB [ 0.250000] SPI_CS ....base f4000000, size 16MB [ 0.250000] BOOT_ROM_CS ....no such [ 0.250000] DEV_BOOTCS ....no such [ 0.250000] CRYPT_ENG ....base f0000000, size 2MB [ 0.250000] [ 0.250000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE [ 0.250000] [ 0.250000] Detected Tclk 200000000 and SysClk 400000000 [ 0.250000] MV Buttons Device Load [ 0.250000] Marvell USB EHCI Host controller #0: c0652600 [ 0.750000] PEX0 interface detected no Link. [ 0.750000] PCI: bus0: Fast back to back transfers enabled [ 0.750000] SCSI subsystem initialized [ 0.750000] usbcore: registered new interface driver usbfs [ 0.750000] usbcore: registered new interface driver hub [ 0.750000] usbcore: registered new device driver usb [ 0.750000] NET: Registered protocol family 2 [ 0.760000] Time: kw_clocksource clocksource has been installed. [ 0.850000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.850000] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.850000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [ 0.850000] TCP: Hash tables configured (established 8192 bind 8192) [ 0.850000] TCP reno registered [ 0.880000] RTC has been updated!!! [ 0.880000] RTC registered [ 0.880000] Use the XOR engines (acceleration) for enhancing the following functions: [ 0.880000] o RAID 5 Xor calculation [ 0.880000] o kernel memcpy [ 0.880000] o kenrel memzero [ 0.880000] Number of XOR engines to use: 4 [ 0.880000] cesadev_init(c00117b0) [ 0.880000] mvCesaInit: sessions=640, queue=64, pSram=f0000000 [ 0.880000] MV Buttons Driver Load [ 0.880000] squashfs: version 3.3 (2007/10/31) Phillip Lougher [ 0.880000] squashfs: LZMA suppport for slax.org by jro [ 0.880000] JFFS2 version 2.2. (NAND) أ‚آ© 2001-2006 Red Hat, Inc. [ 0.880000] io scheduler noop registered [ 0.880000] io scheduler anticipatory registered (default) [ 0.900000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 0.900000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 0.910000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize [ 0.920000] Loading Marvell Ethernet Driver: [ 0.920000] o Cached descriptors in DRAM [ 0.920000] o DRAM SW cache-coherency [ 0.930000] o Single RX Queue support - ETH_DEF_RXQ=0 [ 0.930000] o Single TX Queue support - ETH_DEF_TXQ=0 [ 0.940000] o TCP segmentation offload enabled [ 0.940000] o Receive checksum offload enabled [ 0.950000] o Transmit checksum offload enabled [ 0.950000] o Network Fast Processing (Routing) supported [ 0.960000] o Driver ERROR statistics enabled [ 0.960000] o Driver INFO statistics enabled [ 0.970000] o Proc tool API enabled [ 0.970000] o Rx descripors: q0=128 [ 0.970000] o Tx descripors: q0=532 [ 0.980000] o Loading network interface(s): [ 0.990000] o eth0, ifindex = 1, GbE port = 0 [ 0.990000] o eth1, ifindex = 2, GbE port = 1 [ 1.000000] [ 1.000000] mvFpRuleDb (cfdf6000): 2048 entries, 8192 bytes [ 1.000000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI [ 1.010000] Copyright (c) 1999-2006 Intel Corporation. [ 1.020000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI [ 1.020000] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.030000] [ 1.030000] Warning Sata is Powered Off [ 1.030000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ [ 1.040000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit) [ 1.050000] Scanning device for bad blocks [ 1.100000] Using static partition definition [ 1.110000] Creating 4 MTD partitions on "nand_mtd": [ 1.110000] 0x00000000-0x00100000 : "u-boot" [ 1.120000] 0x00100000-0x00500000 : "uImage" [ 1.120000] 0x00500000-0x02500000 : "root" [ 1.130000] 0x02500000-0x08000000 : "data" [ 1.130000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI [ 1.140000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 [ 1.180000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 [ 1.200000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 1.200000] usb usb1: configuration #1 chosen from 1 choice [ 1.210000] hub 1-0:1.0: USB hub found [ 1.210000] hub 1-0:1.0: 1 port detected [ 1.330000] USB Universal Host Controller Interface driver v3.0 [ 1.610000] usb 1-1: new high speed USB device using ehci_marvell and address 2 [ 1.760000] usb 1-1: configuration #1 chosen from 1 choice [ 1.760000] hub 1-1:1.0: USB hub found [ 1.770000] hub 1-1:1.0: 4 ports detected [ 1.880000] usbcore: registered new interface driver usblp [ 1.880000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver [ 1.890000] Initializing USB Mass Storage driver... [ 1.890000] usbcore: registered new interface driver usb-storage [ 1.900000] USB Mass Storage support registered. [ 1.910000] mice: PS/2 mouse device common for all mice [ 1.910000] i2c /dev entries driver [ 1.910000] Linux telephony interface: v1.00 [ 1.920000] md: linear personality registered for level -1 [ 1.920000] md: raid0 personality registered for level 0 [ 1.930000] md: raid1 personality registered for level 1 [ 2.100000] raid6: int32x1 97 MB/s [ 2.270000] raid6: int32x2 114 MB/s [ 2.440000] raid6: int32x4 122 MB/s [ 2.610000] raid6: int32x8 110 MB/s [ 2.610000] raid6: using algorithm int32x4 (122 MB/s) [ 2.610000] md: raid6 personality registered for level 6 [ 2.620000] md: raid5 personality registered for level 5 [ 2.620000] md: raid4 personality registered for level 4 [ 2.630000] raid5: measuring checksumming speed [ 2.680000] arm4regs : 1071.600 MB/sec [ 2.730000] 8regs : 754.800 MB/sec [ 2.780000] 32regs : 900.000 MB/sec [ 2.780000] raid5: using function: arm4regs (1071.600 MB/sec) [ 2.790000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com [ 2.790000] dm_crypt using the OCF package. [ 2.800000] sdhci: Secure Digital Host Controller Interface driver [ 2.800000] sdhci: Copyright(c) Pierre Ossman [ 2.810000] usbcore: registered new interface driver usbhid [ 2.810000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 2.820000] TCP cubic registered [ 2.820000] NET: Registered protocol family 1 [ 2.830000] NET: Registered protocol family 17 [ 2.830000] md: Autodetecting RAID arrays. [ 2.840000] md: autorun ... [ 2.840000] md: ... autorun DONE. [ 3.070000] VFS: Mounted root (jffs2 filesystem) readonly. [ 3.070000] Freeing init memory: 124K [ 3.070000] Warning: unable to open an initial console. [ 3.080000] Kernel panic - not syncing: No init found. Try passing init= option to kernel. [ 3.090000] Scheduling watchdog timeout to force reboot... U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: PPV2 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 CE>> CE>> CE>>
now i need to know how to fix this issue to run ARM on this box or to return to the default pogoplug image.
Waiting for your help
thanks