Problem installing NSA320 u-boot - continued (3 replies)

Sorted the above out... I noticed it was out of the first mb. I have sucessfully flashed the new u-boot now. :)
However, I can't boot stock zyxel image. It seems that I can boot debian stretch (haven't had time to fully boot it up yet, that's another thing anyway) which I flashed following instructions from https://forum.doozan.com/read.php?2,12096

I think I screwed it up when I should have set

fw_setenv mtdparts 'xxxxxxxxx'

since I didn't had that variable in the backup i took of the environment before, so I just didn't run that.

Any help to restore the ability to boot the stock zyxel image is greatly appreciated. I need to boot up that one one last time to recover data I have in the JOBD partition before going with OMV.

This is the u-boot log:

U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:46:11 -0700)
ZyXEL NSA320 2-Bay Power Media Server

SoC:   Kirkwood 88F6281_A1
DRAM:  512 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
MV88E1318 PHY initialized on egiga0
Hit any key to stop autoboot:  0
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found

Reset IDE: Bus 0: OK Bus 1: OK
  Device 0: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#:  WD-WCC4N6UX02JH
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512)
  Device 1: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#:  WD-WCC4N5JCKKV6
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512)
Unknown command 'mmc' - try 'help'
## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0
loading envs from usb 0 ...
** Bad device usb 0 **

Partition Map for IDE device 0  --   Partition Type: EFI

Part    Start LBA       End LBA         Name
        Attributes
        Type GUID
        Partition GUID
  1     0x00000800      0x000f3fff      "mitraswap"
        attrs:  0x0000000000000000
        type:   0657fd6d-a4ab-43c4-84e5-0933c84b4f4f
        type:   swap
        guid:   8a6ebe8b-87c9-4dc7-9a85-9f670ef809cf
  2     0x000f4000      0x15d509fff     "eexxtt44"
        attrs:  0x0000000000000000
        type:   ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
        type:   data
        guid:   9a279fa3-46de-4fae-b268-e4e15c6064b3


Partition Map for IDE device 1  --   Partition Type: EFI

Part    Start LBA       End LBA         Name
        Attributes
        Type GUID
        Partition GUID
  1     0x00000800      0x000f3fff      "mitraswap"
        attrs:  0x0000000000000000
        type:   0657fd6d-a4ab-43c4-84e5-0933c84b4f4f
        type:   swap
        guid:   31d9fc6d-19db-4264-b8e1-e7f43baed572
  2     0x000f4000      0x15d509fff     "eexxtt44"
        attrs:  0x0000000000000000
        type:   ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
        type:   data
        guid:   b2806883-140c-4bcc-bfdf-39b4a6603f0b
Unknown command 'mmc' - try 'help'
running scan_disk ...
Scan device usb
device usb 0:1
** Bad device usb 0 **
device usb 1:1
** Bad device usb 1 **
device usb 2:1
** Bad device usb 2 **
device usb 3:1
** Bad device usb 3 **
Scan device ide

Reset IDE: Bus 0: OK Bus 1: OK
  Device 0: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#:  WD-WCC4N6UX02JH
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512)
  Device 1: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#:  WD-WCC4N5JCKKV6
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512)
device ide 0:1
** File not found /boot/uImage **
device ide 1:1
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
device ide 2:1
** Bad device ide 2 **
device ide 3:1
** Bad device ide 3 **
Scan device mmc
Unknown command 'mmc' - try 'help'
device mmc 0:1
** Bad device mmc 0 **
device mmc 1:1
** Bad device mmc 1 **
device mmc 2:1
** Bad device mmc 2 **
device mmc 3:1
** Bad device mmc 3 **
loading uImage ...
** Bad device usb 0 **
loading uInitrd ...
** Bad device usb 0 **
loading DTB /boot/dts/kirkwood-nsa320.dtb ...
** Bad device usb 0 **
Wrong Image Format for bootm command
Error occured, error code = 112
ERROR: can't get kernel image!
NSA320>

And here the environment printenv:

arcNumber=3956
bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec
bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
bootdev=usb
device=0:1
devices=usb ide mmc
disks=0 1 2 3
dtb_file=/boot/dts/kirkwood-nsa320.dtb
ethact=egiga0
ethaddr=MY_MAC_IN_RIGHT_FORMAT
fileaddr=1c00000
filesize=0
if_netconsole=ping $serverip
init_ide=ide reset
init_mmc=mmc rescan
init_usb=usb start
ipaddr=192.168.0.231
led_error=orange blinking
led_exit=green off
led_init=green blinking
load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file
load_dtb_addr=0x1c00000
load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd
load_initrd_addr=0x1100000
load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage
load_uimage_addr=0x800000
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start";  setenv scan_ide "ide reset";  setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
scan_ide=ide reset
scan_mmc=mmc rescan
scan_usb=usb start
serverip=192.168.0.220
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_addr=0x810000
uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize
uenv_init_devices=setenv init_usb "usb start";  setenv init_ide "ide reset";  setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices;  do for disknum in 0; do run uenv_read_disk; done; done;
uenv_loaded=0
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read;  fi; else if $devtype part $disknum; then run uenv_read; fi;  fi
usb_ready_retry=15

Environment size: 3144/131068 bytes