uboot env analysis uboot.2013.10-tld-5.ox820.environment (1 reply)

uboot.2013.10-tld-5.ox820.environment

bootdelay=10

ethaddr=52:3b:20:9c:11:51
ethact=mii0

ipaddr=192.168.0.222
#pogo’s ip
serverip=192.168.0.220
# ip of pc running nc or Hercules SETUP utility
if_netconsole=ping $serverip
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
preboot_nc=run if_netconsole start_netconsole
# wihout judge whether pc running nc or Hercules ready or not, start net-console directly

preboot_nc = setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi
# Wait 5 seconds  countdown, which can be broken.And enter net-console when pc running nc or Hercules ready.
preboot = run preboot_nc
# preboot called by uboot 





dtb_file=/boot/dts/ox820-pogoplug-pro.dtb
load_dtb=echo loading DTB $dtb_file ...; ext2load $bootdev $device 0x62c00000 $dtb_file
load_initrd=echo loading uInitrd ...; ext2load $bootdev $device 0x60e00000 /boot/uInitrd
load_uimage=echo loading uImage ...; ext2load $bootdev $device 0x60500000 /boot/uImage




devices=usb ide
# usb ide mmc different types of boot device by sequence
disks=0 1 2 3
# multi disks connected for each usb ide or mmc, eg. usb0 to usb3 when multi usb disk plugged
bootdev=usb
# boot device usb
device=0:1
# boot disk:partition default disk0 partition1

scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start";  setenv scan_ide "ide reset";  setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if ext2load $dev $disknum:1 0x60500000 /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done

#scan each  disks and load uImage from first partition. eg: usb [0-3]:1 ide 0:1 mmc 0:1,set bootdev to (usb)|(ide)|(mmc) device to [0-3]:1


uenv_init_devices=setenv init_usb "usb start";  setenv init_ide "ide reset";  setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;

# init usb, ide or mmc to read uEnv.txt


uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x60500000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi
#load uEnv.txt from first partition of usb [0-3] ide 0 mmc0

uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read;  fi; else if $devtype part $disknum; then run uenv_read; fi;  fi
#what is the functionn? whatever the result of if,run  uenv_read both?
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices;  do for disknum in 0; do run uenv_read_disk; done; done;
#??for disknum in 0?for sentence is for loop but only 0?

uenv_import=echo importing envs ...; env import -t 0x60500000

bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi

mtdids=nand0=41000000.nand
mtdparts=mtdparts=41000000.nand:14m(boot),-(data)
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
# cusom_params no defination

bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm 0x60500000 0x60e00000 0x62c00000; else bootm 0x60500000 0x60e00000; fi; else if run load_dtb; then bootm 0x60500000 - 0x62c00000; else bootm 0x60500000; fi; fi

# according to uimage initrd and dtb,run bootm uimage initrd dtb or bootm uimage initrd or  bootm uimage – dtb or bootm uimage

bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset
# load uenv,then boot



usb_custom_params=zswap.enabled=1
# definition  but not use



mainlineLinux=yes
usb_ready_retry=15
# definition  but not use

stderr=serial
stdin=serial
stdout=serial

uboot.2013.10-tld-5.ox820.environment

bootdelay=10

ethaddr=52:3b:20:9c:11:51
ethact=mii0

ipaddr=192.168.0.222
#pogo’s ip
serverip=192.168.0.220
# ip of pc running nc or Hercules SETUP utility
if_netconsole=ping $serverip
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
preboot_nc=run if_netconsole start_netconsole
# does not judge whether pc running nc or Hercules ready or not, start net-console directly


preboot_nc = \
setenv nc_ready 0;\
for pingstat in 1 2 3 4 5; \
   do; \
      sleep 1;\
      if run if_netconsole; \
         then setenv nc_ready 1; \
      fi; \
   done; \
if test $nc_ready -eq 1; \
then run start_netconsole; \
fi



# Wait 5 seconds  countdown, which can be broken.And enter net-console when pc running nc or Hercules ready.


preboot = run preboot_nc


# preboot called by uboot 

















dtb_file=/boot/dts/ox820-pogoplug-pro.dtb


load_dtb=echo loading DTB $dtb_file ...; ext2load $bootdev $device 0x62c00000 $dtb_file


load_initrd=echo loading uInitrd ...; ext2load $bootdev $device 0x60e00000 /boot/uInitrd


load_uimage=echo loading uImage ...; ext2load $bootdev $device 0x60500000 /boot/uImage














devices=usb ide


# usb ide mmc different types of boot device by sequence


disks=0 1 2 3


# multi disks connected for each usb ide or mmc, eg. usb0 to usb3 when multi usb disk plugged


bootdev=usb


# boot device usb


device=0:1


# boot disk:partition default disk0 partition1





scan_disk=\
echo running scan_disk ...; \
scan_done=0; \
setenv scan_usb "usb start";  \
setenv scan_ide "ide reset";  \
setenv scan_mmc "mmc rescan"; \
for dev in $devices; \
   do \
     if test $scan_done -eq 0; \
        then echo Scan device $dev; \
                 run scan_$dev; \
                 for disknum in $disks; \
                     do \
                          if test $scan_done -eq 0; \
                             then echo device $dev $disknum:1; \
                                    if ext2load $dev $disknum:1 0x60500000 /boot/uImage 1; \
                                       then scan_done=1; \
                                                echo Found bootable drive on $dev $disknum; \
                                                setenv device $disknum:1; \
                                                setenv bootdev $dev; \
                                    fi; \
                          fi; \
                     done; \
     fi; \
   done






#scan each  disks and load uImage from first partition. eg: usb [0-3]:1 ide 0:1 mmc 0:1,set bootdev to (usb)|(ide)|(mmc) device to [0-3]:1








uenv_init_devices=setenv init_usb "usb start";  setenv init_ide "ide reset";  setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;





# init usb, ide or mmc to read uEnv.txt








uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x60500000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi


#load uEnv.txt from first partition of usb [0-3] ide 0 mmc0





uenv_read_disk=\
if test $devtype -eq mmc; \
   then if $devtype part; \
              then run uenv_read;  \
            fi; \
   else if $devtype part $disknum; \
             then run uenv_read; \
           fi;  \
fi



# detect partition and load uenv.txt. due to "mmc part" without following parameter so there is a test. eg,if mmc,run cmd "mmc part" or the 2nd usb disk run cmd "usb part 1"





uenv_load=\
run uenv_init_devices; \
setenv uenv_loaded 0; \
for devtype in $devices;  \
     do \
           for disknum in 0; \
               do run uenv_read_disk; \
               done; \
     done;



#??for disknum in 0?for sentence is for loop but only 0?





uenv_import=echo importing envs ...; env import -t 0x60500000





bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi





mtdids=nand0=41000000.nand


mtdparts=mtdparts=41000000.nand:14m(boot),-(data)


set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params


# cusom_params no defination





bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm 0x60500000 0x60e00000 0x62c00000; else bootm 0x60500000 0x60e00000; fi; else if run load_dtb; then bootm 0x60500000 - 0x62c00000; else bootm 0x60500000; fi; fi





# according to uimage initrd and dtb,run bootm uimage initrd dtb or bootm uimage initrd or  bootm uimage – dtb or bootm uimage





bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset


# load uenv,then boot











usb_custom_params=zswap.enabled=1


# definition  but not use











mainlineLinux=yes


usb_ready_retry=15


# uboot parameter





stderr=serial


stdin=serial


stdout=serial

blue comment is not clear,please help me,
red is another version to enable net-console with judgment, what about this sentence?

what is the function of followed 1?
if ext2load $dev $disknum:1 0x60500000 /boot/uImage 1; \

Latest Images

Trending Articles

Latest Images