Pogoplug Pink E02 can't boot (7 replies)

Hi

I bought a pogoplug to which I could not connect via ssh, but it worked via serial cable - fine. I than devided to install the rescue system, and there I am now: it can't boot anymore. It is in an endless loop and gives me via the serial console:

-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02

SoC:   Kirkwood 88F6281_A0
DRAM:  256 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot:  0
(Re)start USB...
USB:   Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported

** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=3"
UBI: MTD device size:            91 MiB
UBI: number of good PEBs:        728
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     0
UBI: available PEBs:             717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS:   read_nand_cached: error reading nand off 0xc46000 size 8192 bytes
read_nand_cached: error reading nand off 0x15dea00 size 8192 bytes                                                                                                                                        .  read_nand_cached: error reading nand off 0x15ff200 size 8192 bytes
read_nand_cached: error reading nand off 0x161f200 size 8192 bytes
read_nand_cached: error reading nand off 0x163f600 size 8192 bytes                                                                                                                                         done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
resetting ...

I can get into the uboot console, (u-boot>>) but what can I do from herer?

I assume I have an old version of uboot is installed - but how can I install a new version if I can't connect via ssh? Should it be able to boot from a USB drive?

the variables are set as follow:

u-boot>> printenv
arcNumber=2097
baudrate=115200
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
bootdelay=3
console=ttyS0,115200
ethact=egiga0
ethaddr=00:25:31:00:54:02
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
led_error=orange blinking
led_exit=green off
led_init=green blinking
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
partition=nand0,2
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
rescue_installed=0
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
stderr=serial
stdin=serial
stdout=serial
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_device=0:1
usb_init=run usb_scan
usb_root=/dev/sda1
usb_rootdelay=10
usb_rootfstype=ext2
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_scan_list=1 2 3 4
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params

Environment size: 2342/131068 bytes
u-boot>>

Any suggestions what I can do now? Should I try to boot from a USB?

EDIT: bootrom version 1.11 - otherwise I would have tried UART boting as in http://forum.doozan.com/read.php?3,7852,7852