Pogoplug V4 unknown state ? (5 replies)

Installed Debian on it via http://blog.qnology.com/2014/07/hacking-pogoplug-v4-series-4-and-mobile.html

Was working fine, lost power. Couldn't ping it. Wasn't getting an IP address.
Removed debian thumbdrive.
Fired up NC and it appears to stop on "Starting Kernel" (Or from reading the forums it just doesn't display whats going on.
It's not getting an IP. I can't ssh it. The only thing I can do is view Netconsole. I'm not sure what else to do from here or what commands to run to get SSH back.

Pogov4> printenv
 p r i n t e n v 
arcNumber=3960
baudrate=115200
bootcmd=run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset
bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot
bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot;
bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot;
bootdelay=10
console=ttyS0,115200
device=0:1
ethact=egiga0
ethaddr=00:25:31:04:f8:6d
if_netconsole=ping $serverip
ipaddr=192.168.5.190
led_error=orange blinking
led_exit=green off
led_init=green blinking
machid=F78
mainlineLinux=yes
mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
mmc_init=mmc rescan
mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage
mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd
mmc_root=/dev/mmcblk0p1
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
ncip=192.168.5.181
partition=nand0,2
preboot=run if_netconsole start_netconsole
preboot_nc=run if_netconsole start_netconsole
rootdelay=10
rootfstype=ext3
sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
sata_init=ide reset
sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage
sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd
sata_root=/dev/sda1
serverip=192.168.5.181
set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=nc
stdin=nc
stdout=nc
usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_init=usb start
usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage
usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd
usb_root=/dev/sda1
usb_rootfstype=ext3

Environment size: 2311/131068 bytes
Pogov4> 
U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45)
Pogoplug V4
gcc (Debian 4.6.3-14) 4.6.3
GNU ld (GNU Binutils for Debian) 2.22
Hit any key to stop autoboot:  8 
  0 
Pogov4> 
U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45)
Pogoplug V4
gcc (Debian 4.6.3-14) 4.6.3
GNU ld (GNU Binutils for Debian) 2.22
Hit any key to stop autoboot:  0 
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
2461416 bytes read in 427 ms (5.5 MiB/s)
6362802 bytes read in 624 ms (9.7 MiB/s)
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-3.14.0-kirkwood-tld-1
   Created:      2014-04-06  20:44:27 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2461352 Bytes = 2.3 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   initramfs-3.14.0-kirkwood-tld-1
   Created:      2014-04-06  20:44:41 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    6362738 Bytes = 6.1 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK


Starting kernel ...

Help! Not sure what to do to get it back to a working state. I've read different posts for the last 2 hours. I realized I was using an older Uboot. I don't have a serial cable. Is there a way to unplug the debian thumbdrive, mount it on my other linux box and move the newer files onto the drive? (I haven't messed with anything quite like this before.)

The pogoplug had lost power before, I pulled the thumbdrive, ran FSCK from my other linux box and it booted up just fine. Unfortunately this last time that didn't work.

Thanks guys!


EDIT: Also, I tried a bunch of different commands and they didn't work in the NetConsole for the pogoplug. So I'm really lost as to what to do.